Inconel 600 Threaded FlangeASTM B564 · ASME B16.5 · Manufacturer, trader & exporter, India
Alloy 600 · UNS N06600 · THD
An Inconel 600 threaded flange is a flange with a tapered internal thread that screws onto threaded pipe, made from Inconel 600 to ASTM B564. Use a threaded flange where welding is not allowed — for example in explosive areas — on small-bore, low-pressure lines. Threads are NPT to ASME B1.20.1.
- ASTM B564
- ASME B16.5
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an Inconel 600 Threaded Flange?
- What it is
- A flange with a tapered internal thread that screws onto threaded pipe
- Material
- ASTM B564
- Dimensions
- ASME B16.5 · ASME B1.20.1
- Grade
- Inconel 600 · UNS N06600
- Best at
- High-temperature oxidation, caustic and nuclear service
Inconel 600 Threaded Flange Specification
| Product | Inconel 600 Threaded Flange |
|---|---|
| Material standard | ASTM B564 |
| Dimensional standard | ASME B16.5 · ASME B1.20.1 |
| Sizes | ½" – 24" (ASME B16.5) · 26" – 60" (ASME B16.47) |
| Pressure class | Class 150, 300, 400, 600, 900, 1500, 2500 · PN 6 – PN 100 |
| Facing | RF · FF · RTJ · tongue & groove |
| Bore | To match pipe schedule (state on order) |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Threaded Flange
Use a threaded flange where welding is not allowed — for example in explosive areas — on small-bore, low-pressure lines. Threads are NPT to ASME B1.20.1.
- NPT threads to ASME B1.20.1
- Not for cyclic or high-temperature service
- Seal-welding is sometimes added after make-up
More on choosing: Threaded flange guide.
Inconel 600 Threaded Flange: Why 600 for threaded flanges
Use a threaded flange where welding is not allowed — for example in explosive areas — on small-bore, low-pressure lines. Threads are NPT to ASME B1.20.1. In Inconel 600, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy flanges are used where acids, chlorides or heat defeat stainless. Inconel 600 is picked for high-temperature oxidation, caustic and nuclear service. |
|---|---|
| Typical service | Furnaces & heat treating — Muffles, retorts and radiant tubes. |
| B16.5 material group | 3.5 |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Inconel 600 (bar to ASTM B166, where applicable), as the project specifies |
| Welding to carbon steel | A nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel |
| Matching filler | ERNiCr-3 (AWS A5.14) |
Inconel 600 Threaded Flange Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel (+Co) | As specified |
| Chromium | As specified |
| Iron | As specified |
| Carbon | As specified |
| Manganese | As specified |
| Silicon | As specified |
| Copper | As specified |
| Sulphur | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B168 for UNS N06600.
Inconel 600 Threaded Flange Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B168 for UNS N06600 — Annealed plate.
Full chemistry, properties and equivalents are on the Inconel 600 grade page.
Other Inconel 600 flanges
Inconel 600 Threaded Flange dimensions — ASME B16.5 Class 150 & 300
Outside diameter, thickness and bolting are set by size and class. Values in mm; thickness excludes the 1.6 mm raised face.
| NPS | Cl 150 OD | Cl 150 thickness | Cl 150 bolt circle | Cl 150 bolts | Cl 300 OD | Cl 300 thickness | Cl 300 bolt circle | Cl 300 bolts |
|---|---|---|---|---|---|---|---|---|
| ½" | 90 | 9.6 | 60.3 | 4 × ½" | 95 | 12.7 | 66.7 | 4 × ½" |
| 1" | 110 | 12.7 | 79.4 | 4 × ½" | 125 | 15.9 | 88.9 | 4 × ⅝" |
| 1½" | 125 | 15.9 | 98.4 | 4 × ½" | 155 | 19.1 | 114.3 | 4 × ¾" |
| 2" | 150 | 17.5 | 120.7 | 4 × ⅝" | 165 | 20.7 | 127.0 | 8 × ⅝" |
| 3" | 190 | 22.3 | 152.4 | 4 × ⅝" | 210 | 27.0 | 168.3 | 8 × ¾" |
| 4" | 230 | 22.3 | 190.5 | 8 × ⅝" | 255 | 30.2 | 200.0 | 8 × ¾" |
| 6" | 280 | 23.9 | 241.3 | 8 × ¾" | 320 | 35.0 | 269.9 | 12 × ¾" |
| 8" | 345 | 27.0 | 298.5 | 8 × ¾" | 380 | 39.7 | 330.2 | 12 × ⅞" |
| 10" | 405 | 28.6 | 362.0 | 12 × ⅞" | 445 | 46.1 | 387.4 | 16 × 1" |
| 12" | 485 | 30.2 | 431.8 | 12 × ⅞" | 520 | 49.3 | 450.8 | 16 × 1⅛" |
Full chart: ASME B16.5 flange dimensions.
Inconel 600 Threaded Flange — questions buyers ask
Can threaded flanges be used in high-pressure service?
They are rated like other flanges in their class, but threaded joints are not recommended for cyclic, high-temperature or highly corrosive service.
What pressure rating does a Inconel 600 threaded flange have?
It depends on class and temperature. Inconel 600 forgings are in ASME B16.5 material group 3.5; read your class column in that group's table at the design temperature.
Can Inconel 600 threaded flanges be welded to carbon steel?
Yes — a nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel.
Which standard covers Inconel 600 threaded flanges?
The material is ASTM B564; dimensions follow ASME B16.5 · ASME B1.20.1. Always state both on your purchase order, with the edition if your project specifies one.
What decides the price of a Inconel 600 threaded flange?
The alloy price, the size and pressure class, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026