Incoloy 800 / 800H / 800HT WasherUNS N08800 · ASME B18.22.1 · Manufacturer, trader & exporter, India
Alloy 800 · UNS N08800 / N08810 / N08811
An Incoloy 800 / 800H / 800HT washer is a flat or spring ring that spreads bolt load. Finished fastener specification not asserted; material and manufacturing route not asserted — alloy (UNS N08800), dimensions and finished requirements are to the purchase specification. Flat washers protect the joint surface and spread load; spring and lock washers resist loosening. Match the washer material to the bolt to avoid galvanic corrosion.
- UNS N08800
- ASME B18.22.1
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an Incoloy 800 / 800H / 800HT Washer?
- What it is
- A flat or spring ring that spreads bolt load
- Finished spec
- Not asserted
- Material / feedstock
- Not asserted — alloy (UNS N08800), dimensions and finished requirements are to the purchase specification
- Dimensions
- ASME B18.22.1 · DIN 125 (legacy DIN)
- Grade
- Incoloy 800 / 800H / 800HT · UNS N08800
- Best at
- Furnaces, petrochemical heaters and high-temperature piping
Incoloy 800 / 800H / 800HT Washer Specification
| Product | Incoloy 800 / 800H / 800HT Washer |
|---|---|
| Finished fastener specification | Not asserted |
| Material / feedstock specification | Not asserted — alloy (UNS N08800), dimensions and finished requirements are to the purchase specification |
| Dimensional standard | ASME B18.22.1 · DIN 125 (legacy DIN) |
| Manufacturing route | Not asserted |
| Project / purchase specification | Yes — finished fastener requirements are to the purchase specification or project drawing |
| Sizes | To suit M10 – M64 · ½" – 4" bolts (others on request) |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Washer
Flat washers protect the joint surface and spread load; spring and lock washers resist loosening. Match the washer material to the bolt to avoid galvanic corrosion.
- Flat, spring and lock
- ASME B18.21.1 · DIN 125 / 127 (legacy DIN)
- Material to match the bolt
More on choosing: Washer guide.
Incoloy 800 / 800H / 800HT Washer: Why 800 for washers
Flat washers protect the joint surface and spread load; spring and lock washers resist loosening. Match the washer material to the bolt to avoid galvanic corrosion. In Incoloy 800 / 800H / 800HT, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy fasteners match nickel-alloy flanges in corrosive or hot service. Incoloy 800 / 800H / 800HT is picked for furnaces, petrochemical heaters and high-temperature piping. |
|---|---|
| Typical service | Petrochemical — Steam-methane reformer and ethylene furnace piping. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Incoloy 800 / 800H / 800HT (bar to ASTM B408, where applicable), as the project specifies |
Incoloy 800 / 800H / 800HT Washer Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel | As specified |
| Chromium | As specified |
| Iron | As specified |
| Carbon | As specified |
| Aluminium | As specified |
| Titanium | As specified |
| Copper | As specified |
| Manganese | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B409 for UNS N08800 / N08810.
Incoloy 800 / 800H / 800HT Washer Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B409 for UNS N08800 / N08810 — Annealed plate.
Full chemistry, properties and equivalents are on the Incoloy 800 / 800H / 800HT grade page.
Standards on this page
Other Incoloy 800 / 800H / 800HT fasteners
Incoloy 800 / 800H / 800HT Washer — questions buyers ask
Do I need washers on flange bolting?
Many specifications require through-hardened washers under nuts for controlled tightening; follow the project bolting spec.
What nut is used with Incoloy 800 / 800H / 800HT washers?
Usually a nut in the same alloy — it may be machined from ASTM B408 bar, where applicable; finished requirements are to the purchase specification or project drawing.
Which standard covers Incoloy 800 / 800H / 800HT washers?
Finished fastener specification: Not asserted. Material / feedstock: Not asserted — alloy (UNS N08800), dimensions and finished requirements are to the purchase specification. Dimensions: ASME B18.22.1 · DIN 125 (legacy DIN). State the finished specification, material and dimensions on your purchase order or project drawing.
What decides the price of a Incoloy 800 / 800H / 800HT washer?
The alloy price, the size and dimensions, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026