Monel K500 Threaded FlangeASME B16.5 · Manufacturer, trader & exporter, India
Alloy K-500 · UNS N05500 · THD
A Monel K500 threaded flange is a flange with a tapered internal thread that screws onto threaded pipe, made from Monel K500 to project / purchase specification dependent. Use a threaded flange where welding is not allowed — for example in explosive areas — on small-bore, low-pressure lines. Threads are NPT to ASME B1.20.1.
- Monel K500
- ASME B16.5
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is a Monel K500 Threaded Flange?
- What it is
- A flange with a tapered internal thread that screws onto threaded pipe
- Material
- project / purchase specification dependent
- Dimensions
- ASME B16.5 · ASME B1.20.1
- Grade
- Monel K500 · UNS N05500
- Best at
- High-strength pump shafts, bolting and springs in seawater
Monel K500 Threaded Flange Specification
| Product | Monel K500 Threaded Flange |
|---|---|
| Material standard | project / purchase specification dependent |
| Dimensional standard | ASME B16.5 · ASME B1.20.1 |
| Sizes | ½" – 24" (ASME B16.5) · 26" – 60" (ASME B16.47) |
| Pressure class | Class 150, 300, 400, 600, 900, 1500, 2500 · PN 6 – PN 100 |
| Facing | RF · FF · RTJ · tongue & groove |
| Bore | To match pipe schedule (state on order) |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Threaded Flange
Use a threaded flange where welding is not allowed — for example in explosive areas — on small-bore, low-pressure lines. Threads are NPT to ASME B1.20.1.
- NPT threads to ASME B1.20.1
- Not for cyclic or high-temperature service
- Seal-welding is sometimes added after make-up
More on choosing: Threaded flange guide.
Monel K500 Threaded Flange: Why K500 for threaded flanges
Use a threaded flange where welding is not allowed — for example in explosive areas — on small-bore, low-pressure lines. Threads are NPT to ASME B1.20.1. In Monel K500, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy flanges are used where acids, chlorides or heat defeat stainless. Monel K500 is picked for high-strength pump shafts, bolting and springs in seawater. |
|---|---|
| Typical service | Marine — Propeller and pump shafts. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Monel K500 (bar to ASTM B865, where applicable), as the project specifies |
| Welding to carbon steel | A nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel |
| Matching filler | ERNiCu-7 (non-ageing) |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Monel K500 Threaded Flange Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel (+Co) | As specified |
| Copper | As specified |
| Aluminium | As specified |
| Titanium | As specified |
| Iron | As specified |
| Manganese | As specified |
| Carbon | As specified |
| Silicon | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B865 for UNS N05500.
Monel K500 Threaded Flange Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B865 for UNS N05500 — Age-hardened bar.
Full chemistry, properties and equivalents are on the Monel K500 grade page.
Other Monel K500 flanges
Monel K500 Threaded Flange dimensions — ASME B16.5 Class 150 & 300
Outside diameter, thickness and bolting are set by size and class. Values in mm; thickness excludes the 1.6 mm raised face.
| NPS | Cl 150 OD | Cl 150 thickness | Cl 150 bolt circle | Cl 150 bolts | Cl 300 OD | Cl 300 thickness | Cl 300 bolt circle | Cl 300 bolts |
|---|---|---|---|---|---|---|---|---|
| ½" | 90 | 9.6 | 60.3 | 4 × ½" | 95 | 12.7 | 66.7 | 4 × ½" |
| 1" | 110 | 12.7 | 79.4 | 4 × ½" | 125 | 15.9 | 88.9 | 4 × ⅝" |
| 1½" | 125 | 15.9 | 98.4 | 4 × ½" | 155 | 19.1 | 114.3 | 4 × ¾" |
| 2" | 150 | 17.5 | 120.7 | 4 × ⅝" | 165 | 20.7 | 127.0 | 8 × ⅝" |
| 3" | 190 | 22.3 | 152.4 | 4 × ⅝" | 210 | 27.0 | 168.3 | 8 × ¾" |
| 4" | 230 | 22.3 | 190.5 | 8 × ⅝" | 255 | 30.2 | 200.0 | 8 × ¾" |
| 6" | 280 | 23.9 | 241.3 | 8 × ¾" | 320 | 35.0 | 269.9 | 12 × ¾" |
| 8" | 345 | 27.0 | 298.5 | 8 × ¾" | 380 | 39.7 | 330.2 | 12 × ⅞" |
| 10" | 405 | 28.6 | 362.0 | 12 × ⅞" | 445 | 46.1 | 387.4 | 16 × 1" |
| 12" | 485 | 30.2 | 431.8 | 12 × ⅞" | 520 | 49.3 | 450.8 | 16 × 1⅛" |
Full chart: ASME B16.5 flange dimensions.
Monel K500 Threaded Flange — questions buyers ask
Can threaded flanges be used in high-pressure service?
They are rated like other flanges in their class, but threaded joints are not recommended for cyclic, high-temperature or highly corrosive service.
Can Monel K500 threaded flanges be welded to carbon steel?
Yes — a nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel.
Which standard covers Monel K500 threaded flanges?
The finished flange specification is project / purchase specification dependent, so none is named here; dimensions follow ASME B16.5 · ASME B1.20.1. State the flange specification your project requires on the purchase order.
What decides the price of a Monel K500 threaded flange?
The alloy price, the size and pressure class, quantity, and the testing and documents required. Send your list and we quote the same working day.
Can you supply Monel K500 threaded flanges to NACE MR0175?
Yes. Monel K500 is listed in NACE MR0175 / ISO 15156-3 within its limits; state NACE compliance on the order and it is confirmed on the certificate.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026