Monel K500 Orifice FlangeASME B16.36 · Manufacturer, trader & exporter, India
Alloy K-500 · UNS N05500 · ORF
A Monel K500 orifice flange is a pair of weld neck or slip-on flanges with pressure taps that hold an orifice plate, made from Monel K500 to project / purchase specification dependent. Orifice flanges are used for flow measurement. Each flange has two ½" NPT pressure-tap holes, and jack screws help separate the pair to change the plate.
- Monel K500
- ASME B16.36
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is a Monel K500 Orifice Flange?
- What it is
- A pair of weld neck or slip-on flanges with pressure taps that hold an orifice plate
- Material
- project / purchase specification dependent
- Dimensions
- ASME B16.36
- Grade
- Monel K500 · UNS N05500
- Best at
- High-strength pump shafts, bolting and springs in seawater
Monel K500 Orifice Flange Specification
| Product | Monel K500 Orifice Flange |
|---|---|
| Material standard | project / purchase specification dependent |
| Dimensional standard | ASME B16.36 |
| Sizes | 1" – 24" (ASME B16.36) |
| Pressure class | Class 300 – 2500 |
| Facing | RF · FF · RTJ · tongue & groove |
| Bore | To match pipe schedule (state on order) |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose an Orifice Flange
Orifice flanges are used for flow measurement. Each flange has two ½" NPT pressure-tap holes, and jack screws help separate the pair to change the plate.
- Class 300 minimum per ASME B16.36
- Supplied in pairs with jack screws
- Pressure taps: ½" NPT, two per flange
More on choosing: Orifice flange guide.
Monel K500 Orifice Flange: Why K500 for orifice flanges
Orifice flanges are used for flow measurement. Each flange has two ½" NPT pressure-tap holes, and jack screws help separate the pair to change the plate. In Monel K500, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy flanges are used where acids, chlorides or heat defeat stainless. Monel K500 is picked for high-strength pump shafts, bolting and springs in seawater. |
|---|---|
| Typical service | Marine — Propeller and pump shafts. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Monel K500 (bar to ASTM B865, where applicable), as the project specifies |
| Welding to carbon steel | A nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel |
| Matching filler | ERNiCu-7 (non-ageing) |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Monel K500 Orifice Flange Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel (+Co) | As specified |
| Copper | As specified |
| Aluminium | As specified |
| Titanium | As specified |
| Iron | As specified |
| Manganese | As specified |
| Carbon | As specified |
| Silicon | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B865 for UNS N05500.
Monel K500 Orifice Flange Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B865 for UNS N05500 — Age-hardened bar.
Full chemistry, properties and equivalents are on the Monel K500 grade page.
Standards on this page
Other Monel K500 flanges
Monel K500 Orifice Flange — questions buyers ask
Why is the minimum class 300 for orifice flanges?
ASME B16.36 starts at Class 300 so the flange is thick enough to drill the pressure taps radially.
Can Monel K500 orifice flanges be welded to carbon steel?
Yes — a nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel.
Which standard covers Monel K500 orifice flanges?
The finished flange specification is project / purchase specification dependent, so none is named here; dimensions follow ASME B16.36. State the flange specification your project requires on the purchase order.
What decides the price of a Monel K500 orifice flange?
The alloy price, the size and pressure class, quantity, and the testing and documents required. Send your list and we quote the same working day.
Can you supply Monel K500 orifice flanges to NACE MR0175?
Yes. Monel K500 is listed in NACE MR0175 / ISO 15156-3 within its limits; state NACE compliance on the order and it is confirmed on the certificate.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026