ASTM A335 P11 Slip-on FlangeASTM A182 · ASME B16.5 · Manufacturer, trader & exporter, India
SA-335 P11 · 1¼Cr-½Mo alloy pipe · SORF
An ASTM A335 P11 slip-on flange is a flange that slides over the pipe and is fillet-welded inside and outside, for use with ASTM A335 P11 pipe. ASTM A335 P11 itself is a pipe or plate specification, so the matching slip-on flange is made to ASTM A182 F11 — which is what we supply for P11 lines. Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck.
- ASTM A182
- ASME B16.5
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an ASTM A335 P11 Slip-on Flange?
- What it is
- A flange that slides over the pipe and is fillet-welded inside and outside
- Material
- ASTM A182 F11
- Dimensions
- ASME B16.5 · EN 1092-1
- Grade
- ASTM A335 P11
- Best at
- Steam and hot-oil piping up to about 550 °C
ASTM A335 P11 Slip-on Flange Specification
| Product | ASTM A335 P11 Slip-on Flange |
|---|---|
| Material standard | ASTM A182 F11 |
| Dimensional standard | ASME B16.5 · EN 1092-1 |
| Sizes | ½" – 24" (ASME B16.5) · 26" – 60" (ASME B16.47) |
| Pressure class | Class 150, 300, 400, 600, 900, 1500, 2500 · PN 6 – PN 100 |
| Facing | RF · FF · RTJ · tongue & groove |
| Bore | To match pipe schedule (state on order) |
| Testing | Chemical & mechanical per heat · NDT · impact where specified |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Slip-on Flange
Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck.
- Two fillet welds: one at the hub, one inside the bore
- Lower fatigue life than a weld neck in cyclic service
- Available with a hub or as a plate (hubless) design
More on choosing: Slip-on flange guide.
ASTM A335 P11 Slip-on Flange: Why P11 for slip-on flanges
Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck. In ASTM A335 P11, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Carbon and low-alloy flanges carry most utility, hydrocarbon and high-temperature service. ASTM A335 P11 is picked for steam and hot-oil piping up to about 550 °C. |
|---|---|
| Typical service | Power plants — Main steam and reheat lines. |
| B16.5 material group | 1.9 — Group 1.9 applies to A182 F11 Class 2. Chrome-moly welds usually need PWHT; the code sets thickness exemptions. |
| Bolting | ASTM A193 B7 studs with A194 2H nuts; B16 with Gr 4 or 7 nuts where the temperature calls for it |
| Welding to carbon steel | Matching carbon or low-alloy filler is used; joints to stainless need ER309L |
| Matching filler | ER80S-B2 / E8018-B2 |
ASTM A335 P11 Slip-on Flange Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Chromium | As specified |
| Molybdenum | As specified |
| Carbon | As specified |
| Manganese | As specified |
| Silicon | As specified |
| Phosphorus | As specified |
| Sulphur | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM A335 Grade P11.
ASTM A335 P11 Slip-on Flange Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM A335 Grade P11 — condition per order.
Full chemistry, properties and equivalents are on the ASTM A335 P11 grade page.
Other ASTM A335 P11 flanges
ASTM A335 P11 Slip-on Flange dimensions — ASME B16.5 Class 150 & 300
Outside diameter, thickness and bolting are set by size and class. Values in mm; thickness excludes the 1.6 mm raised face.
| NPS | Cl 150 OD | Cl 150 thickness | Cl 150 bolt circle | Cl 150 bolts | Cl 300 OD | Cl 300 thickness | Cl 300 bolt circle | Cl 300 bolts |
|---|---|---|---|---|---|---|---|---|
| ½" | 90 | 9.6 | 60.3 | 4 × ½" | 95 | 12.7 | 66.7 | 4 × ½" |
| 1" | 110 | 12.7 | 79.4 | 4 × ½" | 125 | 15.9 | 88.9 | 4 × ⅝" |
| 1½" | 125 | 15.9 | 98.4 | 4 × ½" | 155 | 19.1 | 114.3 | 4 × ¾" |
| 2" | 150 | 17.5 | 120.7 | 4 × ⅝" | 165 | 20.7 | 127.0 | 8 × ⅝" |
| 3" | 190 | 22.3 | 152.4 | 4 × ⅝" | 210 | 27.0 | 168.3 | 8 × ¾" |
| 4" | 230 | 22.3 | 190.5 | 8 × ⅝" | 255 | 30.2 | 200.0 | 8 × ¾" |
| 6" | 280 | 23.9 | 241.3 | 8 × ¾" | 320 | 35.0 | 269.9 | 12 × ¾" |
| 8" | 345 | 27.0 | 298.5 | 8 × ¾" | 380 | 39.7 | 330.2 | 12 × ⅞" |
| 10" | 405 | 28.6 | 362.0 | 12 × ⅞" | 445 | 46.1 | 387.4 | 16 × 1" |
| 12" | 485 | 30.2 | 431.8 | 12 × ⅞" | 520 | 49.3 | 450.8 | 16 × 1⅛" |
Full chart: ASME B16.5 flange dimensions.
ASTM A335 P11 Slip-on Flange — questions buyers ask
Slip-on or weld neck — which is stronger?
The weld neck. A slip-on flange is fine for moderate pressure and temperature, but in cyclic or severe service engineers specify weld neck flanges.
What pressure rating does a ASTM A335 P11 slip-on flange have?
It depends on class and temperature. ASTM A335 P11 forgings are in ASME B16.5 material group 1.9; read your class column in that group's table at the design temperature.
Can ASTM A335 P11 slip-on flanges be welded to carbon steel?
Yes — matching carbon or low-alloy filler is used; joints to stainless need ER309L.
Which standard covers ASTM A335 P11 slip-on flanges?
The material is ASTM A182 F11; dimensions follow ASME B16.5 · EN 1092-1. Always state both on your purchase order, with the edition if your project specifies one.
What decides the price of a ASTM A335 P11 slip-on flange?
The steel price, the size and pressure class, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026