Inconel 825 Slip-on FlangeASTM B564 · ASME B16.5 · Manufacturer, trader & exporter, India
Incoloy 825 · Alloy 825 · SORF
An Inconel 825 slip-on flange is a flange that slides over the pipe and is fillet-welded inside and outside, made from Inconel 825 to ASTM B564. Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck.
Browse all Inconel 825 flanges on the grade form page.
- ASTM B564
- ASME B16.5
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an Inconel 825 Slip-on Flange?
- What it is
- A flange that slides over the pipe and is fillet-welded inside and outside
- Material
- ASTM B564
- Dimensions
- ASME B16.5 · EN 1092-1
- Grade
- Inconel 825 · UNS N08825
- Best at
- Sulphuric and phosphoric acid service, chloride stress-corrosion cracking and sour gas
Inconel 825 Slip-on Flange Specification
| Product | Inconel 825 Slip-on Flange |
|---|---|
| Material standard | ASTM B564 |
| Dimensional standard | ASME B16.5 · EN 1092-1 |
| Sizes | ½" – 24" (ASME B16.5) · 26" – 60" (ASME B16.47) |
| Pressure class | Class 150, 300, 400, 600, 900, 1500, 2500 · PN 6 – PN 100 |
| Facing | RF · FF · RTJ · tongue & groove |
| Bore | To match pipe schedule (state on order) |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Slip-on Flange
Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck.
- Two fillet welds: one at the hub, one inside the bore
- Lower fatigue life than a weld neck in cyclic service
- Available with a hub or as a plate (hubless) design
More on choosing: Slip-on flange guide.
Inconel 825 Slip-on Flange: Why 825 for slip-on flanges
Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck. In Inconel 825, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy flanges are used where acids, chlorides or heat defeat stainless. Inconel 825 is picked for sulphuric and phosphoric acid service, chloride stress-corrosion cracking and sour gas. |
|---|---|
| Typical service | Sulphuric & phosphoric acid plants — Tank linings, agitators, heat-exchanger baffles in fertiliser and acid production. |
| B16.5 material group | 3.8 — B16.5 does not permit N08825 above 538 °C. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Inconel 825 (bar to ASTM B425, where applicable), as the project specifies |
| Welding to carbon steel | A nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel |
| Matching filler | ERNiFeCr-1 (AWS A5.14) |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Inconel 825 Slip-on Flange Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel | As specified |
| Iron | As specified |
| Chromium | As specified |
| Molybdenum | As specified |
| Copper | As specified |
| Titanium | As specified |
| Carbon | As specified |
| Manganese | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B424 / B423 / B564 for UNS N08825.
Inconel 825 Slip-on Flange Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B424 / B423 / B564 for UNS N08825 — Annealed.
Full chemistry, properties and equivalents are on the Inconel 825 grade page.
Other Inconel 825 flanges
Inconel 825 Slip-on Flange dimensions — ASME B16.5 Class 150 & 300
Outside diameter, thickness and bolting are set by size and class. Values in mm; thickness excludes the 1.6 mm raised face.
| NPS | Cl 150 OD | Cl 150 thickness | Cl 150 bolt circle | Cl 150 bolts | Cl 300 OD | Cl 300 thickness | Cl 300 bolt circle | Cl 300 bolts |
|---|---|---|---|---|---|---|---|---|
| ½" | 90 | 9.6 | 60.3 | 4 × ½" | 95 | 12.7 | 66.7 | 4 × ½" |
| 1" | 110 | 12.7 | 79.4 | 4 × ½" | 125 | 15.9 | 88.9 | 4 × ⅝" |
| 1½" | 125 | 15.9 | 98.4 | 4 × ½" | 155 | 19.1 | 114.3 | 4 × ¾" |
| 2" | 150 | 17.5 | 120.7 | 4 × ⅝" | 165 | 20.7 | 127.0 | 8 × ⅝" |
| 3" | 190 | 22.3 | 152.4 | 4 × ⅝" | 210 | 27.0 | 168.3 | 8 × ¾" |
| 4" | 230 | 22.3 | 190.5 | 8 × ⅝" | 255 | 30.2 | 200.0 | 8 × ¾" |
| 6" | 280 | 23.9 | 241.3 | 8 × ¾" | 320 | 35.0 | 269.9 | 12 × ¾" |
| 8" | 345 | 27.0 | 298.5 | 8 × ¾" | 380 | 39.7 | 330.2 | 12 × ⅞" |
| 10" | 405 | 28.6 | 362.0 | 12 × ⅞" | 445 | 46.1 | 387.4 | 16 × 1" |
| 12" | 485 | 30.2 | 431.8 | 12 × ⅞" | 520 | 49.3 | 450.8 | 16 × 1⅛" |
Full chart: ASME B16.5 flange dimensions.
Inconel 825 Slip-on Flange — questions buyers ask
Slip-on or weld neck — which is stronger?
The weld neck. A slip-on flange is fine for moderate pressure and temperature, but in cyclic or severe service engineers specify weld neck flanges.
What pressure rating does a Inconel 825 slip-on flange have?
It depends on class and temperature. Inconel 825 forgings are in ASME B16.5 material group 3.8; read your class column in that group's table at the design temperature.
Can Inconel 825 slip-on flanges be welded to carbon steel?
Yes — a nickel-base filler such as ERNiCr-3 (or ERNiCrMo-3) is used when joining it to carbon steel.
Which standard covers Inconel 825 slip-on flanges?
The material is ASTM B564; dimensions follow ASME B16.5 · EN 1092-1. Always state both on your purchase order, with the edition if your project specifies one.
What decides the price of a Inconel 825 slip-on flange?
The alloy price, the size and pressure class, quantity, and the testing and documents required. Send your list and we quote the same working day.
Can Inconel 825 slip-on flanges be supplied to NACE MR0175?
Inconel 825 (UNS N08825) can be supplied for sour service when the PO specifies NACE MR0175 / ISO 15156; acceptability depends on the material condition, hardness and the environmental limits in that standard, which the purchaser must confirm for the application.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026