ASTM A106 Gr B Slip-on FlangeASTM A105 · ASME B16.5 · Manufacturer, trader & exporter, India
SA-106 Gr B · Seamless carbon steel pipe · SORF
An ASTM A106 Gr B slip-on flange is a flange that slides over the pipe and is fillet-welded inside and outside, for use with ASTM A106 Gr B pipe. ASTM A106 Gr B itself is a pipe or plate specification, so the matching slip-on flange is made to ASTM A105 — which is what we supply for A106 B lines. Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck.
- ASTM A105
- ASME B16.5
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an ASTM A106 Gr B Slip-on Flange?
- What it is
- A flange that slides over the pipe and is fillet-welded inside and outside
- Material
- ASTM A105
- Dimensions
- ASME B16.5 · EN 1092-1
- Grade
- ASTM A106 Gr B
- Best at
- High-temperature process and steam piping in refineries and power plants
ASTM A106 Gr B Slip-on Flange Specification
| Product | ASTM A106 Gr B Slip-on Flange |
|---|---|
| Material standard | ASTM A105 |
| Dimensional standard | ASME B16.5 · EN 1092-1 |
| Sizes | ½" – 24" (ASME B16.5) · 26" – 60" (ASME B16.47) |
| Pressure class | Class 150, 300, 400, 600, 900, 1500, 2500 · PN 6 – PN 100 |
| Facing | RF · FF · RTJ · tongue & groove |
| Bore | To match pipe schedule (state on order) |
| Testing | Chemical & mechanical per heat · NDT · impact where specified |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Slip-on Flange
Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck.
- Two fillet welds: one at the hub, one inside the bore
- Lower fatigue life than a weld neck in cyclic service
- Available with a hub or as a plate (hubless) design
More on choosing: Slip-on flange guide.
ASTM A106 Gr B Slip-on Flange: Why A106 B for slip-on flanges
Choose a slip-on flange for lower-pressure lines where easy alignment and lower cost matter more than fatigue strength. It needs less precise pipe cutting than a weld neck. In ASTM A106 Gr B, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Carbon and low-alloy flanges carry most utility, hydrocarbon and high-temperature service. ASTM A106 Gr B is picked for high-temperature process and steam piping in refineries and power plants. |
|---|---|
| Typical service | Refineries — Process and steam lines. |
| B16.5 material group | 1.1 |
| Bolting | ASTM A193 B7 studs with A194 2H nuts |
| Welding to carbon steel | Matching carbon or low-alloy filler is used; joints to stainless need ER309L |
| Matching filler | ER70S-6 / E7018 |
ASTM A106 Gr B Slip-on Flange Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Carbon | As specified |
| Manganese | As specified |
| Silicon | As specified |
| Phosphorus | As specified |
| Sulphur | As specified |
| Chromium | As specified |
| Copper | As specified |
| Nickel | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM A106 Grade B.
ASTM A106 Gr B Slip-on Flange Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM A106 Grade B — condition per order.
Full chemistry, properties and equivalents are on the ASTM A106 Gr B grade page.
Other ASTM A106 Gr B flanges
ASTM A106 Gr B Slip-on Flange dimensions — ASME B16.5 Class 150 & 300
Outside diameter, thickness and bolting are set by size and class. Values in mm; thickness excludes the 1.6 mm raised face.
| NPS | Cl 150 OD | Cl 150 thickness | Cl 150 bolt circle | Cl 150 bolts | Cl 300 OD | Cl 300 thickness | Cl 300 bolt circle | Cl 300 bolts |
|---|---|---|---|---|---|---|---|---|
| ½" | 90 | 9.6 | 60.3 | 4 × ½" | 95 | 12.7 | 66.7 | 4 × ½" |
| 1" | 110 | 12.7 | 79.4 | 4 × ½" | 125 | 15.9 | 88.9 | 4 × ⅝" |
| 1½" | 125 | 15.9 | 98.4 | 4 × ½" | 155 | 19.1 | 114.3 | 4 × ¾" |
| 2" | 150 | 17.5 | 120.7 | 4 × ⅝" | 165 | 20.7 | 127.0 | 8 × ⅝" |
| 3" | 190 | 22.3 | 152.4 | 4 × ⅝" | 210 | 27.0 | 168.3 | 8 × ¾" |
| 4" | 230 | 22.3 | 190.5 | 8 × ⅝" | 255 | 30.2 | 200.0 | 8 × ¾" |
| 6" | 280 | 23.9 | 241.3 | 8 × ¾" | 320 | 35.0 | 269.9 | 12 × ¾" |
| 8" | 345 | 27.0 | 298.5 | 8 × ¾" | 380 | 39.7 | 330.2 | 12 × ⅞" |
| 10" | 405 | 28.6 | 362.0 | 12 × ⅞" | 445 | 46.1 | 387.4 | 16 × 1" |
| 12" | 485 | 30.2 | 431.8 | 12 × ⅞" | 520 | 49.3 | 450.8 | 16 × 1⅛" |
Full chart: ASME B16.5 flange dimensions.
ASTM A106 Gr B Slip-on Flange — questions buyers ask
Slip-on or weld neck — which is stronger?
The weld neck. A slip-on flange is fine for moderate pressure and temperature, but in cyclic or severe service engineers specify weld neck flanges.
What pressure rating does a ASTM A106 Gr B slip-on flange have?
It depends on class and temperature. ASTM A106 Gr B forgings are in ASME B16.5 material group 1.1; read your class column in that group's table at the design temperature.
Can ASTM A106 Gr B slip-on flanges be welded to carbon steel?
Yes — matching carbon or low-alloy filler is used; joints to stainless need ER309L.
Which standard covers ASTM A106 Gr B slip-on flanges?
The material is ASTM A105; dimensions follow ASME B16.5 · EN 1092-1. Always state both on your purchase order, with the edition if your project specifies one.
What decides the price of a ASTM A106 Gr B slip-on flange?
The steel price, the size and pressure class, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026