ASTM A333 Gr 6 LateralASTM A420 · MSS SP-43 / manufacturer standard · Manufacturer, trader & exporter, India
SA-333 Gr 6 · Low-temperature carbon steel pipe
An ASTM A333 Gr 6 lateral is a fitting with a 45° branch, for use with ASTM A333 Gr 6 pipe. ASTM A333 Gr 6 itself is a pipe or plate specification, so the matching lateral is made to ASTM A420 WPL6 — which is what we supply for A333 Gr 6 lines. Laterals bring in a branch at 45°, reducing turbulence and pressure drop compared to a tee. Common in drainage, slurry and process lines.
- ASTM A420
- MSS SP-43 / manufacturer standard
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an ASTM A333 Gr 6 Lateral?
- What it is
- A fitting with a 45° branch
- Material
- ASTM A420 WPL6
- Dimensions
- MSS SP-43 / manufacturer standard
- Grade
- ASTM A333 Gr 6
- Best at
- Cold-climate and refrigerated piping down to −45 °C
ASTM A333 Gr 6 Lateral Specification
| Product | ASTM A333 Gr 6 Lateral |
|---|---|
| Material standard | ASTM A420 WPL6 |
| Dimensional standard | MSS SP-43 / manufacturer standard |
| Sizes | ½" – 48" |
| Wall / class | Sch 5S – XXS, to match pipe |
| Ends | Bevelled to ASME B16.25 |
| Testing | Chemical & mechanical per heat · NDT · impact where specified |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Lateral
Laterals bring in a branch at 45°, reducing turbulence and pressure drop compared to a tee. Common in drainage, slurry and process lines.
- 45° branch
- Equal and reducing
- Often fabricated
More on choosing: Lateral guide.
ASTM A333 Gr 6 Lateral: Why A333 Gr 6 for laterals
Laterals bring in a branch at 45°, reducing turbulence and pressure drop compared to a tee. Common in drainage, slurry and process lines. In ASTM A333 Gr 6, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Carbon and low-alloy fittings suit hydrocarbon, steam and utility lines. ASTM A333 Gr 6 is picked for cold-climate and refrigerated piping down to −45 °C. |
|---|---|
| Typical service | LNG & refrigeration — Cold process lines. |
| Welding to carbon steel | Matching carbon or low-alloy filler is used; joints to stainless need ER309L |
| Matching filler | E7018-1 / ER80S-Ni1 |
ASTM A333 Gr 6 Lateral Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Carbon | As specified |
| Manganese | As specified |
| Silicon | As specified |
| Phosphorus | As specified |
| Sulphur | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM A333 Grade 6.
ASTM A333 Gr 6 Lateral Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
| Charpy impact | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM A333 Grade 6 — condition per order.
Full chemistry, properties and equivalents are on the ASTM A333 Gr 6 grade page.
Other ASTM A333 Gr 6 pipe fittings
ASTM A333 Gr 6 Lateral — questions buyers ask
When is a lateral better than a tee?
Where lower turbulence matters — slurries, solids and gravity drainage.
Can ASTM A333 Gr 6 laterals be welded to carbon steel?
Yes — matching carbon or low-alloy filler is used; joints to stainless need ER309L.
Which standard covers ASTM A333 Gr 6 laterals?
The material is ASTM A420 WPL6; dimensions follow MSS SP-43 / manufacturer standard. Always state both on your purchase order, with the edition if your project specifies one.
What decides the price of a ASTM A333 Gr 6 lateral?
The steel price, the size and schedule or class, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026