Duplex 2205 U-boltUNS S32205 · MSS SP-58 / manufacturer standard · Manufacturer, trader & exporter, India
UNS S32205 / S31803 · W.Nr 1.4462
A Duplex 2205 u-bolt is a U-shaped bolt for clamping pipes to supports. Finished fastener specification not asserted; material/feedstock may be supplied to ASTM A276 / A479 (UNS S32205), where applicable; manufacturing route and finished fastener requirements are to the purchase specification or project drawing. U-bolts hold pipes to supports and structures. Sized by pipe NPS with a threaded length on each leg.
- UNS S32205
- MSS SP-58 / manufacturer standard
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is a Duplex 2205 U-bolt?
- What it is
- A U-shaped bolt for clamping pipes to supports
- Finished spec
- Not asserted
- Material / feedstock
- ASTM A276 / A479 (UNS S32205), where applicable
- Dimensions
- MSS SP-58 / manufacturer standard
- Grade
- Duplex 2205 · UNS S32205
- Best at
- Strength with chloride resistance at a stainless-steel budget
Duplex 2205 U-bolt Specification
| Product | Duplex 2205 U-bolt |
|---|---|
| Finished fastener specification | Not asserted |
| Material / feedstock specification | ASTM A276 / A479 (UNS S32205), where applicable |
| Dimensional standard | MSS SP-58 / manufacturer standard |
| Manufacturing route | Route dependent on product design and purchase specification |
| Project / purchase specification | Yes — finished fastener requirements are to the purchase specification or project drawing |
| Sizes | M10 – M64 · ½" – 4" (others on request) |
| Threads | UNC · UN-8 · metric coarse |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose an U-bolt
U-bolts hold pipes to supports and structures. Sized by pipe NPS with a threaded length on each leg.
- Sized to pipe NPS
- With nuts and plates
- Matching or isolated material
More on choosing: U-bolt guide.
Duplex 2205 U-bolt: Why 2205 for u-bolts
U-bolts hold pipes to supports and structures. Sized by pipe NPS with a threaded length on each leg. In Duplex 2205, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Duplex fasteners add strength in chloride service. Duplex 2205 is picked for strength with chloride resistance at a stainless-steel budget. |
|---|---|
| Typical service | Oil & gas — Flowlines, manifolds and topside piping. |
| Bolting | B7 (coated), B8M or duplex studs, as the project specifies |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Duplex 2205 U-bolt Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Chromium | As specified |
| Nickel | As specified |
| Molybdenum | As specified |
| Nitrogen | As specified |
| Carbon | As specified |
| Manganese | As specified |
| Silicon | As specified |
| Phosphorus | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM A240 for UNS S32205.
Duplex 2205 U-bolt Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
| Hardness | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM A240 for UNS S32205 — Solution-annealed plate & sheet.
Full chemistry, properties and equivalents are on the Duplex 2205 grade page.
Standards on this page
Other Duplex 2205 fasteners
Duplex 2205 U-bolt — questions buyers ask
Should U-bolts match the pipe material?
Use the same alloy, or an isolating sleeve, to avoid galvanic corrosion between pipe and bolt.
What nut is used with Duplex 2205 u-bolts?
Usually a nut in the same alloy — it may be machined from ASTM A276 / A479 bar, where applicable; finished requirements are to the purchase specification or project drawing.
Which standard covers Duplex 2205 u-bolts?
Finished fastener specification: Not asserted. Material / feedstock: ASTM A276 / A479 (UNS S32205), where applicable. Dimensions: MSS SP-58 / manufacturer standard. State the finished specification, material and dimensions on your purchase order or project drawing.
What decides the price of a Duplex 2205 u-bolt?
The alloy price, the size and dimensions, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026