Inconel 825 U-boltUNS N08825 · MSS SP-58 / manufacturer standard · Manufacturer, stockist & exporter, India
Incoloy 825 · Alloy 825
An Inconel 825 u-bolt is a U-shaped bolt for clamping pipes to supports. Finished fastener specification not asserted; material/feedstock may be supplied to ASTM B425 (UNS N08825), where applicable; manufacturing route and finished fastener requirements are to the purchase specification or project drawing. U-bolts hold pipes to supports and structures. Sized by pipe NPS with a threaded length on each leg.
- UNS N08825
- MSS SP-58 / manufacturer standard
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is an Inconel 825 U-bolt?
- What it is
- A U-shaped bolt for clamping pipes to supports
- Finished spec
- Not asserted
- Material / feedstock
- ASTM B425 (UNS N08825), where applicable
- Dimensions
- MSS SP-58 / manufacturer standard
- Grade
- Inconel 825 · UNS N08825
- Best at
- Sulphuric and phosphoric acid service, chloride stress-corrosion cracking and sour gas
Inconel 825 U-bolt Specification
| Product | Inconel 825 U-bolt |
|---|---|
| Finished fastener specification | Not asserted |
| Material / feedstock specification | ASTM B425 (UNS N08825), where applicable |
| Dimensional standard | MSS SP-58 / manufacturer standard |
| Manufacturing route | Route dependent on product design and purchase specification |
| Project / purchase specification | Yes — finished fastener requirements are to the purchase specification or project drawing |
| Sizes | M10 – M64 · ½" – 4" (others on request) |
| Threads | UNC · UN-8 · metric coarse |
| Testing | PMI · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 · 3.2 with third-party inspection |
When to Choose an U-bolt
U-bolts hold pipes to supports and structures. Sized by pipe NPS with a threaded length on each leg.
- Sized to pipe NPS
- With nuts and plates
- Matching or isolated material
More on choosing: U-bolt guide.
Inconel 825 U-bolt: Why 825 for u-bolts
U-bolts hold pipes to supports and structures. Sized by pipe NPS with a threaded length on each leg. In Inconel 825, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy fasteners match nickel-alloy flanges in corrosive or hot service. Inconel 825 is picked for sulphuric and phosphoric acid service, chloride stress-corrosion cracking and sour gas. |
|---|---|
| Typical service | Sulphuric & phosphoric acid plants — Tank linings, agitators, heat-exchanger baffles in fertiliser and acid production. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Inconel 825 (bar to ASTM B425, where applicable), as the project specifies |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Inconel 825 U-bolt Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel | As specified |
| Iron | As specified |
| Chromium | As specified |
| Molybdenum | As specified |
| Copper | As specified |
| Titanium | As specified |
| Carbon | As specified |
| Manganese | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B424 / B423 / B564 for UNS N08825.
Inconel 825 U-bolt Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B424 / B423 / B564 for UNS N08825 — Annealed.
Full chemistry, properties and equivalents are on the Inconel 825 grade page.
Standards on this page
Other Inconel 825 fasteners
Inconel 825 U-bolts for export
FOB / CIF · Nhava Sheva (JNPT), MumbaiInconel 825 U-bolt — questions buyers ask
Should U-bolts match the pipe material?
Use the same alloy, or an isolating sleeve, to avoid galvanic corrosion between pipe and bolt.
What nut is used with Inconel 825 u-bolts?
Usually a nut in the same alloy — it may be machined from ASTM B425 bar, where applicable; finished requirements are to the purchase specification or project drawing.
Which standard covers Inconel 825 u-bolts?
Finished fastener specification: Not asserted. Material / feedstock: ASTM B425 (UNS N08825), where applicable. Dimensions: MSS SP-58 / manufacturer standard. State the finished specification, material and dimensions on your purchase order or project drawing.
What decides the price of a Inconel 825 u-bolt?
The alloy price, the size and dimensions, quantity, and the testing and documents required. Send your list and we quote the same working day.
Can you supply Inconel 825 u-bolts to NACE MR0175?
Yes. Inconel 825 is listed in NACE MR0175 / ISO 15156-3 within its limits; state NACE compliance on the order and it is confirmed on the certificate.
What documents do you supply?
EN 10204 3.1 mill certificates as standard, 3.2 with third-party inspection on request, plus dimensional and PMI reports.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026