Monel K500 Threaded RodUNS N05500 · DIN 976-1:2016-09, Form A, where applicable · Manufacturer, trader & exporter, India
Alloy K-500 · UNS N05500
A Monel K500 threaded rod is a continuously threaded bar cut to length. Finished fastener specification not asserted; material/feedstock may be supplied to ASTM B865 (UNS N05500), where applicable; manufacturing route and finished fastener requirements are to the purchase specification or project drawing. Threaded rod is cut to make studs and hangers. Available in full lengths or cut pieces.
- UNS N05500
- DIN 976-1:2016-09, Form A, where applicable
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is a Monel K500 Threaded Rod?
- What it is
- A continuously threaded bar cut to length
- Finished spec
- Not asserted
- Material / feedstock
- ASTM B865 (UNS N05500), where applicable
- Dimensions
- DIN 976-1:2016-09, Form A, where applicable
- Grade
- Monel K500 · UNS N05500
- Best at
- High-strength pump shafts, bolting and springs in seawater
Monel K500 Threaded Rod Specification
| Product | Monel K500 Threaded Rod |
|---|---|
| Finished fastener specification | Not asserted |
| Material / feedstock specification | ASTM B865 (UNS N05500), where applicable |
| Dimensional standard | DIN 976-1:2016-09, Form A, where applicable |
| Manufacturing route | Route dependent on product design and purchase specification |
| Project / purchase specification | Yes — finished fastener requirements are to the purchase specification or project drawing |
| Sizes | M10 – M64 · ½" – 4" (others on request) |
| Threads | UNC · UN-8 · metric coarse |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose a Threaded Rod
Threaded rod is cut to make studs and hangers. Available in full lengths or cut pieces.
- 1 m and 3 m lengths
- Cut to size
- UNC, UN-8 and metric
More on choosing: Threaded rod guide.
Monel K500 Threaded Rod: Why K500 for threaded rods
Threaded rod is cut to make studs and hangers. Available in full lengths or cut pieces. In Monel K500, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy fasteners match nickel-alloy flanges in corrosive or hot service. Monel K500 is picked for high-strength pump shafts, bolting and springs in seawater. |
|---|---|
| Typical service | Marine — Propeller and pump shafts. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Monel K500 (bar to ASTM B865, where applicable), as the project specifies |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Monel K500 Threaded Rod Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel (+Co) | As specified |
| Copper | As specified |
| Aluminium | As specified |
| Titanium | As specified |
| Iron | As specified |
| Manganese | As specified |
| Carbon | As specified |
| Silicon | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B865 for UNS N05500.
Monel K500 Threaded Rod Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B865 for UNS N05500 — Age-hardened bar.
Full chemistry, properties and equivalents are on the Monel K500 grade page.
Standards on this page
Other Monel K500 fasteners
Monel K500 Threaded Rod — questions buyers ask
Is threaded rod the same as a stud bolt?
Stud bolts are cut from threaded rod or threaded to length and supplied with nuts, to flange-bolting dimensions.
What nut is used with Monel K500 threaded rods?
Usually a nut in the same alloy — it may be machined from ASTM B865 bar, where applicable; finished requirements are to the purchase specification or project drawing.
Which standard covers Monel K500 threaded rods?
Finished fastener specification: Not asserted. Material / feedstock: ASTM B865 (UNS N05500), where applicable. Dimensions: DIN 976-1:2016-09, Form A, where applicable. State the finished specification, material and dimensions on your purchase order or project drawing.
What decides the price of a Monel K500 threaded rod?
The alloy price, the size and dimensions, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026