Monel K500 Eye BoltUNS N05500 · Project drawing / purchase specification · Manufacturer, trader & exporter, India
Alloy K-500 · UNS N05500
A Monel K500 eye bolt is a bolt with a loop head for lifting or anchoring. Finished fastener specification not asserted; material/feedstock may be supplied to ASTM B865 (UNS N05500), where applicable; manufacturing route and finished fastener requirements are to the purchase specification or project drawing. Eye bolts provide lifting points on equipment. Load ratings depend on angle of pull.
- UNS N05500
- Project drawing / purchase specification
- EN 10204 3.1 / 3.2
- Export packing
Reviewed by the Kanak Steel & Engineering Co. technical team · Updated October 2026
What is a Monel K500 Eye Bolt?
- What it is
- A bolt with a loop head for lifting or anchoring
- Finished spec
- Not asserted
- Material / feedstock
- ASTM B865 (UNS N05500), where applicable
- Dimensions
- Project drawing / purchase specification
- Grade
- Monel K500 · UNS N05500
- Best at
- High-strength pump shafts, bolting and springs in seawater
Monel K500 Eye Bolt Specification
| Product | Monel K500 Eye Bolt |
|---|---|
| Finished fastener specification | Not asserted |
| Material / feedstock specification | ASTM B865 (UNS N05500), where applicable |
| Dimensional standard | Project drawing / purchase specification |
| Manufacturing route | Route dependent on product design and purchase specification |
| Project / purchase specification | Yes — finished fastener requirements are to the purchase specification or project drawing |
| Sizes | M10 – M64 · ½" – 4" (others on request) |
| Threads | UNC · UN-8 · metric coarse |
| Testing | PMI (as specified in the PO) · dimensional · NDT and IGC on request |
| Documents | EN 10204 3.1 or 3.2 on request / as specified in the PO |
When to Choose an Eye Bolt
Eye bolts provide lifting points on equipment. Load ratings depend on angle of pull.
- Forged or machined to drawing
- Load rating per design and purchase specification
- Metric and inch
More on choosing: Eye bolt guide.
Monel K500 Eye Bolt: Why K500 for eye bolts
Eye bolts provide lifting points on equipment. Load ratings depend on angle of pull. In Monel K500, the choice usually comes down to the medium and temperature — the rows here are the points buyers check for this exact combination.
| Why this grade | Nickel-alloy fasteners match nickel-alloy flanges in corrosive or hot service. Monel K500 is picked for high-strength pump shafts, bolting and springs in seawater. |
|---|---|
| Typical service | Marine — Propeller and pump shafts. |
| Bolting | B7 (coated), B8M or nickel-alloy studs in Monel K500 (bar to ASTM B865, where applicable), as the project specifies |
| Sour service | Listed in NACE MR0175 / ISO 15156-3 within its limits — state it on the order |
Monel K500 Eye Bolt Chemical Composition
Under technical review for TDS.
| Element | Current requirement |
|---|---|
| Nickel (+Co) | As specified |
| Copper | As specified |
| Aluminium | As specified |
| Titanium | As specified |
| Iron | As specified |
| Manganese | As specified |
| Carbon | As specified |
| Silicon | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification to be verified: ASTM B865 for UNS N05500.
Monel K500 Eye Bolt Mechanical Properties
Under technical review for TDS.
| Property | Current requirement |
|---|---|
| Tensile strength | As specified |
| Yield strength 0.2% | As specified |
| Elongation | As specified |
Numerical specification requirements are published only after the applicable current standard edition has been verified. Governing specification and condition to be verified: ASTM B865 for UNS N05500 — Age-hardened bar.
Full chemistry, properties and equivalents are on the Monel K500 grade page.
Standards on this page
Other Monel K500 fasteners
Monel K500 Eye Bolt — questions buyers ask
Can eye bolts be loaded at an angle?
Only shouldered eye bolts, and with a reduced rating; follow the load chart.
What nut is used with Monel K500 eye bolts?
Usually a nut in the same alloy — it may be machined from ASTM B865 bar, where applicable; finished requirements are to the purchase specification or project drawing.
Which standard covers Monel K500 eye bolts?
Finished fastener specification: Not asserted. Material / feedstock: ASTM B865 (UNS N05500), where applicable. Dimensions: Project drawing / purchase specification. State the finished specification, material and dimensions on your purchase order or project drawing.
What decides the price of a Monel K500 eye bolt?
The alloy price, the size and dimensions, quantity, and the testing and documents required. Send your list and we quote the same working day.
What documents do you supply?
EN 10204 3.1 or 3.2 certificates available on request / as specified in the PO; dimensional reports as required. PMI can be arranged depending on product and requirements, as specified in the PO.
Sources: the ASTM / ASME specifications named on this page and producer datasheets · Last updated October 2026